Tape Pancakes: NAB Hub Storage Explained
If you are searching for professional reel-to-reel tape transfer services, you may have noticed that most reel-to-reel tape comes on a metal or plastic reel, but maybe your tape does not. Reels are the norm. Some tapes instead arrive as "pancakes": magnetic tape wound tightly on a bare NAB hub without flanges.
A pancake can look damaged or neglected, but it is an established archival method for 1/4", 1/2", 1", and 2" reel-to-reel tape. Knowing why it exists helps you prepare your collection for digitization.
What Is a Tape Pancake?
A tape pancake is magnetic tape stored on a central NAB hub without flanges. With no discs on either side, the tape forms a self-supporting cylinder, held together by a slow, low-tension wind called a Library Wind.
When the wind is done correctly, the edges line up and the pack holds its shape without flanges. Professional archives use this method, especially for legacy studio masters.
Archivists did not invent the pancake. It started as a way for studios to save money. In the 1950s and 60s, magnetic tape was one of the most expensive line items in a studio budget, and a single 10-inch reel of 2-inch multitrack tape cost hundreds of dollars. Studios could not afford to let reels sit idle.
Studios reused tape constantly. A multitrack master might be recorded, mixed, erased, and reused within weeks. Full NAB reels with flanges were heavy, bulky, and too expensive to dedicate to recordings that might be erased next month.
Bare NAB hubs were cheap, light, and stackable. A studio could strip the flanges after mixing, store the tape as a pancake, and put the flanges back to work for the next session. The flanges became shared equipment, and only the tape stayed with the recording.
Archives inherited the practice. When preservation professionals began systematically archiving commercial recordings in the 1970s, they inherited libraries already full of pancaked tapes. Rather than remount millions of feet of tape onto flanged reels, conservators studied the existing practice and found that tapes stored as pancakes were often in better condition than tapes kept on reels. A cost-saving habit turned out to be a better way to store tape.
Why Pancakes Protect Tape: Flanges, Tension, Print-Through and Storage
Once archives saw these benefits, they turned the economic shortcut into a formal conservation practice. The same benefits affect how well your tape digitizes.
No flange damage. Over decades, plastic flanges warp and metal flanges bend. A bent flange presses unevenly on the tape pack, scoring and deforming the edge, which is where tape is most easily damaged. Without flanges, that damage cannot happen, and the transfer has fewer dropouts and cleaner audio.
Less weight on the shelves. A 2-inch multitrack master on a heavy precision NAB reel weighs about 12 pounds. Across thousands of reels, that adds up to a heavy load on archive shelving. Pancakes drop the weight of the reels, so shelves carry less and can hold tapes more densely and safely.
Handling has to be deliberate. A pancake cannot be grabbed carelessly, which makes it safer to handle. Operators load it onto a machine with a mounting plate or demountable flanges. That rules out a common mistake with reels: squeezing the flanges together to stop the tape slipping, which crushes the tape edges and leaves artifacts in the transfer.
Stress relief for the tape pack. Tape wound under high tension onto a rigid flanged reel traps mechanical stress in the plastic backing. On an open core, under controlled climate conditions, the pack can relax and settle without flanges pressing on its sides.
Many people believe tight winding prevents print-through. It makes print-through worse: higher pressure forces the oxide layers into closer contact, which speeds up signal transfer between wraps.
Archivists control print-through in two ways, neither of which involves winding tightness:
- Tails-Out Storage: Storing tape rewound to the end turns pre-echo into post-echo, where the audio that follows masks it.
- Cool Storage: Lower temperatures slow the magnetic migration that causes print-through.
An archival pancake is also never wound by fast-forwarding. High-speed winding traps air pockets and leaves a jagged "scattered pack." A proper Library Wind runs at play speed or slower, with calibrated tension. Tapes wound this way transfer better than tapes wound at a machine's fast-wind speed.
The standard practice is to store pancakes flat (horizontally), for three reasons:
- Preventing Slippage: Stored on edge, a pancake stays on its hub only through friction between the tape layers and the hub. Over time, especially with heavier 1-inch and 2-inch tape, gravity can make the pack slip or fall off the hub. Stored flat, it stays put.
- Supporting the Weight: Lying flat, the pack's weight spreads across the box or shelf, so the outer layers are not crushed or distorted by the layers below them.
- Stability: Flat pancakes shift less during handling and transport, which matters when shipping tapes for professional transfer.
When you store a pancake flat, use a box deep enough to hold the tape, with spacers or dividers to keep the pack from moving in transit.
Handling and Preparing Pancakes, Format by Format
The same storage logic applies to every tape width, but handling gets harder as the tape gets wider and heavier, both in storage and during the transfer.
| Format | Primary Use | Storage & Transfer Notes |
|---|---|---|
| 1/4" | Stereo masters, broadcast, field recordings | The most common pancake format. Prone to edge curl if it was stored against warped plastic flanges, so inspect the edges before dismounting. Properly pancaked 1/4" tape usually gives the cleanest transfers. |
| 1/2" | 2-track mixdowns, 4 or 8-track sessions | The heavier pack needs careful tension control. If the wind is uneven, inner layers can slip off the core when the flanges come off. Professional transfer machines can compensate for small inconsistencies. |
| 1" | 8 or 16-track studio sessions | Always use hold-down leader tape. Support the pack with both hands when it is unbolted: it is stiff enough to hold its shape but brittle enough to crack if mishandled. Multitrack transfer needs specialized alignment. |
| 2" | 24-track analog masters | Very heavy. Handle with center-support plates, and store flat to prevent hub slippage. These are the highest-value transfers and need the most careful pancake preparation. |
Making an archival pancake takes care. A badly wound pancake loses the benefits above and transfers worse.
Required materials:
- Tape deck with adjustable or calibrated wind tension
- NAB hubs (clean, undamaged)
- Acid-free archival paper hold-down tabs
- Inert polyethylene sleeves and acid-free boxes
- Lint-free cotton gloves
Step-by-step procedure:
- Inspect Before Winding: Check for sticky-shed syndrome. If the tape squeals, sheds oxide, or feels gummy, it has to be baked before it goes near a winding deck. Do not pancake a sick tape. Baking should be done by a professional before the tape is sent for transfer.
- Perform a Library Wind: Play the tape through at standard speed or slower, with calibrated low tension. This lines up the edges and releases stress left by earlier winds.
- Park Tails-Out: Stop the wind at the tail of the tape, so any print-through echo falls after the audio.
- Secure the Tail: Use acid-free paper tabs or archival hold-down tape on the leader only. Never put adhesive on the magnetic oxide.
- Dismount Flanges Carefully: With the core resting on a flat support plate, remove the flanges gently, supporting the sides of the pack as you go.
- Box Horizontally: Slide the pancake into an inert sleeve, put it in an acid-free box with hub support pads, and store it flat. Do not stand pancake boxes on edge.
When you're ready to convert your pancaked reels to lossless digital WAV files, trust Deep Signal Studios for professional reel-to-reel transfer services. For more on keeping a collection playable, see saving your reel-to-reel tape collection and acetate reels and vinegar syndrome.
Frequently Asked Questions
Why are the flanges removed?
To save weight, space and money. Flanges add weight and bulk to every reel, and a 2-inch master on a precision NAB reel weighs about 12 pounds, so a bare hub is lighter to store, stacks, and frees the flanges for reuse.
Can I play a tape pancake directly on my home reel-to-reel machine?
No. Without support, a pancake spills off the core as soon as tension is applied. Mount it on removable flanges or on a bottom support plate made for NAB hubs.
Should I clean the tape while winding it into a pancake?
No. Pulling tape through cleaning blocks under winding tension drags unevenly, can scratch the oxide, and can break old splices. Cleaning is a separate restoration step done before the archival wind, ideally by a trained technician before transfer.
Why horizontal storage specifically?
Because of gravity. Stored on edge, a pancake stays on its hub only through friction, which can give way over time, especially with heavy 2-inch tape. Stored flat, the weight spreads evenly and the pack does not slip during long-term storage or shipping.
Is pancaking still used for cost savings today?
Yes, by studios working with new tape, where the cost argument still holds. Archives preserving older recordings now use it mainly for conservation and only secondarily for convenience. Cost savings started the practice, and the preservation benefits, including better transfers, kept it going.